The compact LittleRed X2D-30 features a high powered boost zone that can surge substrate temperatures to over 300°F (149°C) within the first several inches of conveyor travel inside the 27 in. (68.6 cm) heating chamber.
Two 24 in. (61 cm) wide, height-adjustable infrared heaters and dual zone heat controls maintain consistent temperatures needed for precise cure rates. Rapid preheating maximizes the dwell time allowing increased conveyor belt speeds and oven output.
The heaters, 6,300W @ 240V total wattage, carry an industry-leading 15-year warranty, and feature closely spaced coils to provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing.
The unit is equipped with a powered exhaust system as standard to rapidly remove moisture and air contaminates from the heating chamber, as well as to cool the skin and controls.
Model X2D-30 has a 30 in. (76.2 cm) wide conveyor belt, with overall conveyor length of 66 in. (167.7 cm). A low friction belt aligner and belt speed controls to precisely set dwell times from 35 seconds up to four minutes.
A Teflon®-coated fiberglass belt with alignment tracking system is standard. Stainless steel mesh belts for high-heat and/or sanitary applications are optional.
The capacity (belt speed) of LittleRed™ X1D, LittleRed™ X2D, LittleRed™ X3D, EconoRed™ III Series, and BigRed™ 4D (shown) conveyor ovens can be doubled or tripled as new or when needs increase by simply adding one or two modular heating chambers and extending the conveyor belt. This eliminates the need to invest in a larger oven than you need at the onset, and avoids the high cost of purchasing a new oven when your needs increase.
Heater Warranty | 15 Year | ||
Defect Warranty | 3 Year | ||
Belt Speed | 0.7-9.3 FPM (0.2-2.8 MPM) | ||
Belt Motor Torque | 100 in-lb | ||
Exhaust (Free Air) | 280 CFM (7.9 CMM) | ||
Exhaust Diameter | 6" (15.3 cm) | ||
Overall Length | 66" (167.7 cm) | ||
Overall Width | 41" (104.2 cm) | ||
Overall Height | 50" (127 cm) | ||
Belt Width | 30" (76.2 cm) | ||
Heater Width | 24" (61 cm) | ||
Recommended Curable Width | 18" (45.8 cm) | ||
Chamber Length | 27" (68.6 cm) | ||
Chamber Infeed Width | 33.5" (85.1 cm) | ||
Chamber Infeed Height (adjustable) | 2" -7" (5 - 17.7 cm) | ||
Heat Range (@ Heater) | 0-900°F (0-482°C) @ 240V 0-1150°F (0-621°C) - booster |
||
Total Wattage | 6,300 Watts | ||
Electrical Specs** All dryers 50/60HZ |
240V / 27A / 1 Ph. / 3 wire | ||
Optional Power | Also available in 3 phase -240V / 380V | ||
Unit Weight | 380 lbs (173 kg) | ||
Conveyor Belt Material | Teflon® coated fiberglass standard, Kevlar® mesh, Food grade, and other TPI available. (Limit 550°F/288°C) | ||
**All amps shown are FLA (Full Load Amps), not recommended line size! Ovens on this page must be hard-wired to the power terminal provided. A licensed electrician must be consulted and should refer to articles 210.20(a), 215.3 and 310 of the NEC code. |